Reention Rhino battery connector (6 pins)

This connector is suitable for Dengfu E55, E56 frame batteries.

The price include male and female connector.

The original Dengfu E55/E56 battery would have a battery communication, our wires have no battery communication leads, please note. The battery can work normally without the battery communication being connected. 

Power cable for Dorado battery, Tigershark case, Atlas case or other Reention casing battery with PLA 0273 male connector , 5 pin PLA 0049 or 6 pin PLA 0238 connector; If you order the power cable, it is better for you to choose Ø4mm bullet connector, Ø5mm bullet connector or bare wire for the end connector for controller/motor because there is a small wire rubber O seal on the mounting, other connectors would be too big to go though the wire seal(you may need to let the wire go through the wire O seal, then solder the larger connectors). The connector is soldered with cable which you can replace your old plug on the battery easily by removing the lock screw.

If you need a extension cable or conversion wire for your battery, then the big connector is not a problem. But please make sure you choose the right male or female connector when placing the order.

This power cable is suitable for the Atlas casing battery, 36V Dorado battery, 48V Dorado batteries or the Tigershark casing battery. 

The 2 pin PLA 0273 connector is the male connector(installed in the battery mounting base), it's matching 2 pin female connector is PLA 0274 connector which is installed on the battery body;  Note, the PLA 0274 looks like 5 pin connector, but the three small pins are empty, therefore we call it "2 pin" connector.

The 5 pin PLA 0049 connector is the male connector(installed in the battery mounting base), it's matching 5 pin female connector is PLA 0050 connector which is installed on the battery body;

The 6 pin PLA 0238 connector is the male connector(installed in the battery mounting base), it's matching 6 pin female connector is PLA 0239 connector which is installed on the battery body;

The default wires are 12 AWG wire, if you need 10AWG wire, please email us separately. By the way, 10AWG wire for power cable, they may be too large for the wire seal of the mounting unless you discard the wire seal when installing the power cable.

e bike rear rack battery casing end cap with handle and charging port. If your end cap of the rear rack battery is broken, you can consider this one for replacement. There are many types rear rack cases, please double check your own one before placing the order. The end cap is also suitable for our own ebike rear rack casing battery.

e-bike rear rack battery end cap with key lock /fuse /discharging port

Hailong connector with cable soldered for Hailong battery mounting; it is easy for you to replace the new connector with the old one in your mounting. If you don't have soldering tool available, this power cable would be more convenience for you to replace it. Note: this power cable only includes the 4/5pin connectors with cable soldered, if you need the plug for connecting your motor controller, we can solder for you too. The counter plug from the battery body is not included. 

There are two types Hailong connector, one is with 4 blade contacts and the other is with 5 golden round contacts, the picture shows the 4pins; we also have 5pins for your option.

There is a "+ " and "-" marks on the Hailong original connector, and we solder the red wire(positive) to + and black wire(negative) to the - as default. Please double check your own plug which one for positive and which one for negative before plugping it to your motor controller.

How to replace the Hailong connector:

Bafang BBS power cable for extension or conversion.

The connector can be BBS01/02 default bullet connector, BBSHD Anderson connector, Amass XT60 connector, Amass XT90 connector.

Cable length could be 10-100cm for your demand;

Wre: 12AWG black/red wire;

If your current Bafang motor and the battery are with different connector, then you may need a conversion cable.

If your ebike battery power cable is too short, then you may need a extension cable. 

e-bike fuel tank battery case for large AH battery, it can max hold 117pcs 18650 Cells or 91pcs 21700 cells. There are two types of fuel tank battery cases, the mounting bases are the same, the only difference is the height please note. 

Battery level is available for the case; the charging port is 5.5X2.1 or 5.5x2.5DC port.

The larger AH you have for your battery, the more mileage you can get for single charge.

Size: 381 x 183 x 126mm 91pcs 18650 cells or 65pcs 21700 cells;

Size: 381 x183 x 167mm for 117pcs 18650 cells or 91pcs 21700 cells;

Key set for Hailong downtube HL-02 casing battery.

This key lock is only suitable for downtube Hailong-02 casing battery.

How to replace Hailong key lock, please check the video below:

Charging cable with 5.5DC*2.5DC connector;

Charging port: 5.5*2.5DC port, 5.5*2.1DC port; charging port is installed on our Hailong-01 battery case , polly DP-6 battery case, tigeshark DS-6 case or frame DA-5C battery case.

There are two types of this kind of connector, 5.5*2.5DC and 5.5*2.1DC;  2.5DC connector is normally used for charging current ≥4A; 2.1DC connector is used for charging current <4A;

The male 5.5*2.5DC connector is compatible with 2.1 and 2.5DC port; if you are not sure your charging port is 2.1 port or 2.5 port, you can choose the 2.5DC connector.

If your original connector is damaged, you can just cut the old plug, wire with new connector with the small red cable and black cable;  Our 2.5DC connector is with red anode and black cathode as default. For your original charger, it would be better for you to identify the positive and negative cables before wire the new connector.

Note: the space between the contacts are close, it's better to make the other two contacts insulated when soldering to avoid the welder touching other contacts causing a short circuit.

For how to change to the 5.5X2.1DC or 5.5X2.5DC cable from inside of the charger, please check below video: