Connectors and cables
-
$0.50JST JWPF 02R/02T/03R/03T /04R/04T/06R/06T08R/08T connectors
JST JWPF VSLE 02R/02T/03R/03T/04R/04T/06R/06T08R/08T connectors for Bafang MM max drive G330 controller, sensor connecting or Bafang Ultra G510 controller, sensor connecting. Contacts are included. -
$5.00Hailong casing battery power cable
Hailong connector with cable soldered for Hailong battery mounting; it is easy for you to replace the new connector with the old one in your mounting. If you don't have soldering tool available, this power cable would be more convenience for you to replace it. Note: this power cable only includes the 4/5pin connectors with cable soldered, if you need the plug for connecting your motor controller, we can solder for you too. The counter plug from the battery body is not included.
There are two types Hailong connector, one is with 4 blade contacts and the other is with 5 golden round contacts, the picture shows the 4pins; we also have 5pins for your option.
There is a "+ " and "-" marks on the Hailong original connector, and we solder the red wire(positive) to + and black wire(negative) to the - as default. Please double check your own plug which one for positive and which one for negative before plugping it to your motor controller.
How to replace the Hailong connector: -
$9.509 pin motor extension wire with waterproof connector
9 pin motor extension wire with waterproof connector; this cable is suitable for standard 250W/350W motor.
This extension wire is compatible with our own 9 pin motor wires.
Wire length: 100cm
-
$4.00Bafang BBS01 BBS02 BBSHD power cable for extension or conversion
Bafang BBS power cable for extension or conversion.
The connector can be BBS01/02 default bullet connector, BBSHD Anderson connector, Amass XT60 connector, Amass XT90 connector.
Cable length could be 10-100cm for your demand;
Wre: 12AWG black/red wire;
If your current Bafang motor and the battery are with different connector, then you may need a conversion cable.
If your ebike battery power cable is too short, then you may need a extension cable.
-
$2.00e-bike donwtube battery connector with cable 5.5*2.5DC/5.5x2.1DC connector
Charging cable with 5.5DC*2.5DC connector;
Charging port: 5.5*2.5DC port, 5.5*2.1DC port; charging port is installed on our Hailong-01 battery case , polly DP-6 battery case, tigeshark DS-6 case or frame DA-5C battery case.
There are two types of this kind of connector, 5.5*2.5DC and 5.5*2.1DC; 2.5DC connector is normally used for charging current ≥4A; 2.1DC connector is used for charging current <4A;
The male 5.5*2.5DC connector is compatible with 2.1 and 2.5DC port; if you are not sure your charging port is 2.1 port or 2.5 port, you can choose the 2.5DC connector.
If your original connector is damaged, you can just cut the old plug, wire with new connector with the small red cable and black cable; Our 2.5DC connector is with red anode and black cathode as default. For your original charger, it would be better for you to identify the positive and negative cables before wire the new connector.
Note: the space between the contacts are close, it's better to make the other two contacts insulated when soldering to avoid the welder touching other contacts causing a short circuit.
For how to change to the 5.5X2.1DC or 5.5X2.5DC cable from inside of the charger, please check below video:
