Motor cable with 9 pin waterproof connector, male and female; male cable length 0.4m; female cable length: 85cm, 100cm or 150cm for option

If you order the female part, please also choose the motor hall connectors; if you don't choose the motor hall connectors, we will ship with the connector randomly.

If you don't know which connectors to choose, you can check our controllers, our controllers use the 6P DJ7061 connectors and 2.8pins for motor hall as default.

If you need longer wire for the motor, you can add a 9pin extension motor wire for your motor.

9 pin motor extension wire with waterproof connector; this cable is suitable for standard 250W/350W motor.

This extension wire is compatible with our own 9 pin motor wires. 

Wire length: 100cm

KT speed sensor for KT controller or KT LCD1, LCD2, LCD3, LCD4, LCD5, LCD7U, LCD8, LCD9 etc.

Cable length: 1.5m

Plug: Molex 3P(fit for GBK's KT series controllers)

MTB Crankset Puller/ Crank Arm Remover/ bike squal hole/spline bottom axis remover

The cap is used for spline bottom only; if your bike is with squal hole bottom, please ignore the cap.

Plier for C clip ring.

For replacing Bafang front or rear nylon gear, Bafang BBS magnet disc, BBS pinion steel gear, you may need this plier to remove the C clip ring.

This C clip ring does not fit for SWXK/SWXH/SWXK02/SWXK05 motor 36T nylon gear's clip ring, please note.

E-bike 6V LED headlight suitable for Bafang BBS. Input: AC6V ; Cable length: 1.5M

Connector matching for Bafang BBS01/BBS02B controller's headlight plug, red wire for positive, blue wire for negative.

DPC18 display has a "headlight" button; for 965 and 961 display, press "+" button and hold for 3 seconds, the headlight will switch on/off.

If you use it for Ultra M620 mid motor, Bafang M400 motor, M420 or Bafang M300 motor, this 6V LED headlight will also be suitable for these mid drive motors. Please make sure you have the Bafang motor light connection cable.

Wuxing headlight and  speaker for bicycle. We also provide a Wuxing two in one switch for the headlight.  The matching connectors will be provided with the headlight and switch. The headlight is suitable for a 12V-80V battery.

If you also need a rear light for your ebike, we also provide 6V LED taillight suitable for 6V-60V batteries. The rear light can be installed on the e-bike rack or the seatpost tube.

The bike is installed on the front fork as shown in the picture.

Headlight Waterproof grade: IPX4

All the cables and connectors will be soldered before shipping.  If you ordered the battery on our website, we will order the matching connector with the battery too. If not, you may need to solder the two power cables to your battery mounting. If you don't want to do the soldering job, you can order an extra mounting on our website, and we will solder the matching discharging connector and light power cable/connector for you. We provide varies battery mountings for backup. 

bike/MTB threaded freewheel removing tool; If your bike is with cassette freewheel, please order this one: MTB cassette freewheel removing tool

Bicycle multi function tool sets including flat/phillips screwdriver,  Hexagon(Allen) key, nut tools, and  socket wrench. It is lightweight and portable. It is a must for bike riders.

Bolts for 8fun bbs01 or bbs02 chainring adapter. This bolt is also suitable for some mountain bike chainring. Please refer to our drawing and check the length you need before ordering.

bike cassette freewheel removing tool, including two tools, one tool to discrew the nuts and the other tool to prevent the freewheel to roate.

E-bike rear light 6V LED

1. Input: DC 6V-60V

2. Output: 6V

3. Power: 0.6W

4 It can be powered by your ebike battery from 6V to 60V;

5. Cable length:  1.5M

6. You may need an ON/OFF switch to control the rear light;

7. This rear light can be mounted on the bike rear rack or on the seatpost tube. We will provide the matching backet.

8. If you also need a ebike headlight, you can order on our website, we can solder the rear light and head light to be controlled by one on/off switch.

KT-V12L Kunteng Dual hall 12 poles, 12 magnets pedal assisting sensor for ebike; it is easy to install on left side of the BB.

Cable length: 80cm 

Cable connection: 

Brown wire ---> +5v

Black wire---> Negative Electrode

Yellow wire ---> Signal

Note: This PAS only work with KT controller. Also,Kunteng controller normally set C1 = 2 as a defaullt setting for the 8 pole PAS, if you want to use 12 poles PAS, please set C1 =6 via the display, otherwise the PAS may not work.

Fatbike motor cable for Bafang 750W RM G06 snow bike hub motor.

The female cable length is 80cm, the phase wire adapts Φ5 BBS bullet connector which can bear larger current.

The extension cable length is 110cm.

Split 12 magnets dual hall sensor with higher accuracy for electric bikes. It is easy to install with the split PAS. No need to remove the crank; Only plug the split magnets arount the bottom bracket axle, then fix the sensor on the seat tube.

The PAS fits our KT series controllers.

Ebike brushless hub motor spare parts, washers, nuts etc., end plastic cap, or Bafang rear hub motor freewheel spacer.

Ebike fuel tank battery which is designed to install in the motorcycle fuel tank position. It can also be installed on the frame down-tube. 

ABS controller case for ebike controller;

Small case is suitable for  250W controller-GBK-CON611, CON621 or CON63, can be mounted on the frame of bicycle;

Larger case is suitable for CON94 350W controller, can be mounted on ebike frame;

Rear rack for e-bike rack battery.

This rack is only suitable for 26" bike with V-brake. It will not suitable for disc brake bike, please note. 

The rack is suitable for our rack battery.