Bafang M620 /M400
-
$18.00Bafang Ultra motor plastic cover/ Bafang Ultra M620 plastic cover
Bafang Ultra motor plastic cover / Bafang Ultra M620 plastic cover for replacement.
-
$4.00Bafang BBS01 BBS02 BBSHD power cable for extension or conversion
Bafang BBS power cable for extension or conversion.
The connector can be BBS01/02 default bullet connector, BBSHD Anderson connector, Amass XT60 connector, Amass XT90 connector.
Cable length could be 10-100cm for your demand;
Wre: 12AWG black/red wire;
If your current Bafang motor and the battery are with different connector, then you may need a conversion cable.
If your ebike battery power cable is too short, then you may need a extension cable.
-
$8.00 As low as: $6.00Bafang BBS /Ultra M620 /M400 /M500 /M600 half twist throttle
Bafang BBS half twist throttle for BBS01, BBS02, BBSHD, Max Drive M400, M420, M500, M600, Ultra M620 G510 mid motor(A pair including grip handle). Wuxing brand throttle and Higo connector. You can choose right hand or left hand.
This half twist throttle is also suitable for Ultra M620/ G510 mid motor.
Note: This throttle also fit for Bafang Max Drive M400 G330 motor, but you need to change to a 1T4 EB-BUS, otherwise you cannot connect the throttle to your Max drive unit.
-
Bafang e-brake grip for BBS / M620/ M400 /M420 /M600 /M410 etc
Bafang mid crank kit bbs01 and bbs02 brake grip.
This e-brake fits for all the Bafang motors with round Higo connector.
-
$6.65Bafang M600 M510 M560 M630 M820 CANbus motor display extension cable
Original Bafang M600 M510 M560 M630 M820 M620(CANbus), M400(CANbus), M410 motor display extension cable.
This cable is suitable for all the Bafang CAN-bus display.
Cable length: 200mm.
-
$145.00Bafang Besst tool
Bafang Besst tool for Bafang motor calibration, speed setting, firmware refreshing.
Important note: The Bafang Besst tool needs Bafang's access account to log in, hence to calibrate or refreshing the Bafang products. If you don't have the account, please don't order this tool, otherwise this tool is useless.
-
$14.50Bafang M400 /G330 /G350 /AEG Bafang max drive Pawl Clutch
Bafang max drive clutch/ Bafang M400 finger freewheel for replacement; If your M400 MAX Drive is not smooth when pedaling, then consider the pawl clutch is defective.
How to replace the Bafang Max drive M400 G330 pawl clutch, please check the video below:
-
$80.00Bafang Max drive/Bafang M400 steel reduction gear set with cover
Bafang M400 reduction gear for replacement; the Bafang max drive steel cover is included.
The item includes motor gasket, reduction gear and gear cover/motor casing as shown in the picture.
For how to replace the reduction gear cover, please refer to the following vedio.
-
$105.00Bafang max drive /Bafang M400 Motor controller (UART /CAN)
Bafang max drive M400 G330 motor controller(UART protocol) for replacement. If your motor is with CAN protocol, this controller will not fit. Please double check before ordering.
The Bafang M400 controllers has several parameters, 36V 250W, 36V 350W, 43V 350W or 48V 350W controllers, please check your own motor before placing the order.
If you want a headlight for your bike, you can add a pair Bafang MAX M400 G330 headlight/rearlight cable and a LED headlgiht with the controller.
Note: if your original motor is with coaster brake, this controller may not fit.
Bafang has two protocols for the max drive mid motor, UART or CAN protocol. How to identify? UART protocol controllers no need calibration; CAN protocol controllers may needs calibration.
UART protocol controller will have a "U" mark on the controller, it's EB-BUS connector is with female connector and the display for the motor would be UART protocol with a 5 pin round connector.If the display connector is with triangle connector, then it is with CAN protocol. The back of the display may also mark “CAN” .
The controllers we are selling is with UART protocol and it will not fit for CAN protocol motor. please double check before ordering.
If your original controller is 48V 13A, then you can choose 48V 13A controller for replacement. Bafang has upgraded to 13A controller for the 48V motor.
How to replace the Bafang Max drive M400 G330 controller, please check the video below:
-
$106.00Bafang Max drive /Bafang M400 /G330 torque sensor (UART)
Bafang Max drive MM M400 G330 axle with torque sensor;
The axle provided by Bafang fits for Bafang M400 G330 mid motor.
The length for the axle is 151mm.
There are two versions for Max drive mid motor, standard e-brake motor and coaster brake(pedal brake) mid motor; and the torque sensor for them are different.
There are two protocols for the torque sensors, CAN and UART protocol; For how to identify the motor is UART or CAN protocol, please check our pictures on the M400 controller page. There is another way to identify. UART protocol torque sensor connectors are with the female connectors which are shown on our pictures; the CAN torque sensor is with the male connectors.
How to replace the Bafang max drive M400 G330 torque sensor, please check below video:
