Bafang M400 G330 G33 motor sealing gasket; if you open your motor, the gasket would be violated, then you may need a new gasket.  

Bafang Max drive core, including Bafang M400 stator or rotor for replacement.

Bafang M400 motor core is easy to disassemble and replace.

The Bafang MAX drive M400 G330 motor core are sourced directly from Bafang.

If your motor is CAN protocol, this stator or motor core would not fit for your motor. 

How to check your motor is CAN or UART protocol? Please check from the M400 controller or the Bafang display connector;

The UART protocol controller will have a "U" mark on the controller, it's EB-BUS connector is with female connector and the display for the motor would be UART protocol with a 5 pin round connector.
If the display connector is with triangle connector, then it is with CAN protocol. The back of the display may also mark “CAN".

Replacing the CAN motor core, you may need to recalibrate the motor.

For how to replace the motor core, please check video below:

Bafang max drive MM G330 Motor nylon gear with bearing for replacement；

There would be two versions for the Nylon gear, one is with 4mm gap depth, and the other is with 6mm gap depth.

The height of the bearing is 46mm with 4mm gap gear; the bearing height for 6mm gap gear is 44mm. The two Max drive bearing sets are not compatible. 

44mm gear set is the old version while 46mm gear set is the new version, please check your original bearing before placing the order.

The solo nylon gear only fits for 46mm gear set.

For details, please check the picture for the gear; please double check before placing order. 

Bafang MAX drive m400 G330 chainwheel- 38T;

Bafang M300 M200 motor share the same MTB chainwheel with M400 motor.

Bafang M300, M400, M620, G330, G360, G510 UART EB-BUS cable.

Bafang Max drive cable, main harness 1T3, connecting the display, a pair of e-brakes, cable length: 1.2m;

Bafang Max drive cable, main harness 1T2, connecting the display and one brake, cable length: 1.2m;

Bafang Max drive cable, main harness 1T1, connecting the display, for coaster brake system, cable length: 1.5m

If your original Max drive unit is with 1T1 EB-BUS and you want to add a throttle function for your ebike, please choose the 1T4 EB-BUS. The throttle function only works after starting with pedaling the ebike, please note.  

If your original Max drive unit is with 1T3 EB-BUS and you want to add a throttle function for your ebike, please choose the 1T4 EB-bus. The throttle function only works after starting with pedaling the ebike, please note.  Important tips: the throttle for the Bafang M400 motor only works under load with the pedal speed reaching 10km/h.

The display connector is with 5 pin round connector which means for UART protocol, not for CAN protocol, please note.

Bafang BBS crank arm; bafang M400 /m300 crank arms

Bafang Max drive M400 /G330 barebone motor.

If your motor is "old age" and defective, you can buy a new barebone motor to replace it.

The default protocol for our barebone M400 motor is UART, please note. 

How to check your max drive G330 motor is UART or CAN protocol? Check the original display connector, UART protocol is with round 5pin connector display which CAN protocol is with 5pin triangle connector display.

If you need complete set of Max drivec M400, please email us.

Bafang M400 G330 motor take apart:

Bafang Max Ddrive M400 G330 mid motor installation screw kit

Bafang MAX drive mounting plate;

Bafang M400 hanger.