Accessories
-
MTB Crankset Puller/ Crank Arm Remover/ bike squal hole/spline bottom axis remover
MTB Crankset Puller/ Crank Arm Remover/ bike squal hole/spline bottom axis remover
The cap is used for spline bottom only; if your bike is with squal hole bottom, please ignore the cap.
-
bike/MTB threaded freewheel removing tool
bike/MTB threaded freewheel removing tool; If your bike is with cassette freewheel, please order this one: MTB cassette freewheel removing tool
-
Bicycle multi-function tool sets for repair or e-bike conversion
Bicycle multi function tool sets including flat/phillips screwdriver, Hexagon(Allen) key, nut tools, and socket wrench. It is lightweight and portable. It is a must for bike riders.
-
$1.00 As low as: $0.60
Bafang bbs kit chainring adapter bolts
Bolts for 8fun bbs01 or bbs02 chainring adapter. This bolt is also suitable for some mountain bike chainring. Please refer to our drawing and check the length you need before ordering.
-
bike/MTB cassette freewheel removing tool
bike cassette freewheel removing tool, including two tools, one tool to discrew the nuts and the other tool to prevent the freewheel to roate.
-
Bicycle B B axle wrench tools
Bicycle b b axle wrench tools for assembling E-bike PAS. -
E-bike hub motor spare parts
Ebike brushless hub motor spare parts, washers, nuts etc., end plastic cap, or Bafang rear hub motor freewheel spacer.
-
Electric bicycle spoke wrenches
Bicycle spoke wrenches suitable for different spoke specification. -
$2.00 As low as: $1.80
e-bike gas/accelerator/Twist Grip Throttle
ebike accelerator/gas, e-bike throttle; cable length 1.5m
Connection: Red->+5v, black->GND, Green-> signal
-
$3.00 As low as: $2.80
E-bike brake grip/e-brake/ebike cut-off
e-brake for e-bike, brake grip,
Cable length: 1.5m
-
Bafang BBS01 BBS02 BBSHD power cable for extension or conversion
Bafang BBS power cable for extension or conversion.
The connector can be BBS01/02 default bullet connector, BBSHD Anderson connector, Amass XT60 connector, Amass XT90 connector.
Cable length could be 10-100cm for your demand;
Wre: 12AWG black/red wire;
If your current Bafang motor and the battery are with different connector, then you may need a conversion cable.
If your ebike battery power cable is too short, then you may need a extension cable.
-
Hailong (hailong 01/02/03) battery connector/socket(4 pin /5 pin /6 pin) male and female
Hailong case discharging connector 4 blade contacts, 5 round contacts or 6 round contacts, fit for Hailong 01, Hailong 02 or Hailong 03 casing battery. Please note They are not suitable for Hailong 01 Pro battery; the hailong 01 Pro case use 5 blade contacts connector al though the housing is similar but not compatible.
There are 3 types of connectors for Hailong case, the outter dimensions are the same, only the contacts are different, one is with 4 blade contacts, one is with 5 golden round contacts and the rest is with 6 round coontacts. Please check your own Hailong connectors before placing the order.
20A< 4 pin connector<25A; 25A <5 pin connector <30A;
30A < 6 pin connector <35A;
-
e-bike motor hall/ throttle/ ebrake connector DJ7061A-2.8-11/21 male/female plug
e-bike motor hall connector DJ7061A-2.8-11/21 male/female plug; this plug is normally used for motor hall, ebike brake, e bike gas/throttle end connection.
6P plug for motor hall;
3P plug for e-bike throttle/gas;
2P plug for e-brake;
Plug sping and male tab are included.
-
Controller power cable for ebike battery or controller
E-bike power cord for connecting motor controller to ebike battery.
For connecting motor controller side, the connector could be DJ7031 connector(we no longer use it) , Φ4mm bullet connector(default power connector of our front or rear ebike controllers) or Φ5mm bullet connector(default power connector for Bafang BBS01/02 kit).
For connecting battery side, you can choose your demand connectors.
Currently, 90% front or rear brushless motor controller use Φ4mm bullet connectors for motor controller. You can check your own controller power connectors before ordering.
Default cable would be 14AWG.
If you need 12AWG wire for the power cable, please leave a message.
-
e-bike motor phase/controller power/TSDZ2 motor bullet connector 4.0/4.2mm with housing
electric bike motor phase connector green bullet connector male/famale with isolated cover;
Ebike brushless controlle power connector bullet type male/female with housing;
Bullet connector 4.0mm/4.2mm for battery/motor phase/controller power connection.
The price includes male and female bullet connector, amle and female isolated protector.
This connector is suitable for Tongsheng TSDZ2 mid motor power plug.