MTB Crankset Puller/ Crank Arm Remover/ bike squal hole/spline bottom axis remover

The cap is used for spline bottom only; if your bike is with squal hole bottom, please ignore the cap.

bike/MTB threaded freewheel removing tool; If your bike is with cassette freewheel, please order this one: MTB cassette freewheel removing tool

Bicycle multi function tool sets including flat/phillips screwdriver,  Hexagon(Allen) key, nut tools, and  socket wrench. It is lightweight and portable. It is a must for bike riders.

Bolts for 8fun bbs01 or bbs02 chainring adapter. This bolt is also suitable for some mountain bike chainring. Please refer to our drawing and check the length you need before ordering.

bike cassette freewheel removing tool, including two tools, one tool to discrew the nuts and the other tool to prevent the freewheel to roate.

Ebike brushless hub motor spare parts, washers, nuts etc., end plastic cap, or Bafang rear hub motor freewheel spacer.

ebike accelerator/gas, e-bike throttle; cable length 1.5m

Connection: Red->+5v, black->GND, Green-> signal

e-brake for e-bike, brake grip,

Cable length: 1.5m

Bafang BBS power cable for extension or conversion.

The connector can be BBS01/02 default bullet connector, BBSHD Anderson connector, Amass XT60 connector, Amass XT90 connector.

Cable length could be 10-100cm for your demand;

Wre: 12AWG black/red wire;

If your current Bafang motor and the battery are with different connector, then you may need a conversion cable.

If your ebike battery power cable is too short, then you may need a extension cable. 

Hailong case discharging connector 4 blade contacts, 5 round contacts or 6 round contacts, fit for Hailong 01, Hailong 02 or Hailong 03 casing battery.  Please note They are not suitable for Hailong 01 Pro battery; the hailong 01 Pro case use 5 blade contacts connector al though the housing is similar but not compatible.

There are 3 types of connectors for Hailong case, the outter dimensions are the same, only the contacts are different, one is with 4 blade contacts, one is with 5 golden round contacts and the rest is with 6 round coontacts. Please check your own Hailong connectors before placing the order.

20A< 4 pin connector<25A; 25A <5 pin connector <30A; 

 30A < 6 pin connector <35A;

e-bike motor hall connector DJ7061A-2.8-11/21 male/female plug; this plug is normally used for motor hall, ebike brake, e bike gas/throttle end connection.

6P plug for motor hall;

3P plug for e-bike throttle/gas;

2P plug for e-brake;

Plug sping and male tab are included.

E-bike power cord for connecting motor controller to ebike battery.

For connecting motor controller side, the connector could be DJ7031 connector(we no longer use it) , Φ4mm bullet connector(default power connector of our front or rear ebike controllers) or Φ5mm bullet connector(default power connector for Bafang BBS01/02 kit).

For connecting battery side, you can choose your demand connectors.

Currently, 90% front or rear brushless motor controller use Φ4mm bullet connectors for motor controller. You can check your own controller power connectors before ordering.

Default cable would be 14AWG.

If you need 12AWG wire for the power cable, please leave a message.

electric bike motor phase connector green bullet connector male/famale with isolated cover;

Ebike brushless controlle power connector bullet type male/female with housing;

Bullet connector 4.0mm/4.2mm for battery/motor phase/controller power connection.

The price includes male and female bullet connector, amle and female isolated protector.

This connector is suitable for Tongsheng TSDZ2 mid motor power plug.

4/5 pins connector for e-bike lithium ion battery, for rear rack casing, downtube silver fish casing. There may be different connectors for rear rack or filverfish casing battery, please check the dimension of the original connector before ordering.

ebike Atlas frame battery mouting foot.

This mounting is suitable for our downtube Atlas casing battery(DA-5C).

The price is only for the mouting, not including the battery case.

We will solder the power connector before shipment if you also add the power connector with the frame battery attachment.

The default discharging connector of the mountin is 2P original plug, please note. If you need 6P plug for larger current, please email us after placing the order.

ebike battery downtube case mounting on bike frame with slim dimension(hailing 1 case).

Discharging port is 4pin, charging port is round 5.5x2.1 or 5.5x2.5DC connector. If you want larger charging current, please choose 2.5DC charging port.

Cell holders and battery mounting foot are included with the case. If you also need the matching BMS/PCM for this casing battery, you can click here for the bms.

Atlas frame battery key lock  or Jumbo shark battery.  . 

If you are not sure which case the key set uses for, please check dimension or pictures for our Atlas frame battery case and Jumbo shark battery case.