E-bike 6V LED headlight suitable for Bafang BBS. Input: AC6V ; Cable length: 1.5M

Connector matching for Bafang BBS01/BBS02B controller's headlight plug, red wire for positive, blue wire for negative.

DPC18 display has a "headlight" button; for 965 and 961 display, press "+" button and hold for 3 seconds, the headlight will switch on/off.

If you use it for Ultra M620 mid motor, Bafang M400 motor, M420 or Bafang M300 motor, this 6V LED headlight will also be suitable for these mid drive motors. Please make sure you have the Bafang motor light connection cable.

Wuxing headlight and  speaker for bicycle. We also provide a Wuxing two in one switch for the headlight.  The matching connectors will be provided with the headlight and switch. The headlight is suitable for a 12V-80V battery.

If you also need a rear light for your ebike, we also provide 6V LED taillight suitable for 6V-60V batteries. The rear light can be installed on the e-bike rack or the seatpost tube.

The bike is installed on the front fork as shown in the picture.

Headlight Waterproof grade: IPX4

All the cables and connectors will be soldered before shipping.  If you ordered the battery on our website, we will order the matching connector with the battery too. If not, you may need to solder the two power cables to your battery mounting. If you don't want to do the soldering job, you can order an extra mounting on our website, and we will solder the matching discharging connector and light power cable/connector for you. We provide varies battery mountings for backup. 

Fatbike motor cable for Bafang 750W RM G06 snow bike hub motor.

The female cable length is 80cm, the phase wire adapts Φ5 BBS bullet connector which can bear larger current.

The extension cable length is 110cm.

Split 12 magnets dual hall sensor with higher accuracy for electric bikes. It is easy to install with the split PAS. No need to remove the crank; Only plug the split magnets arount the bottom bracket axle, then fix the sensor on the seat tube.

The PAS fits our KT series controllers.

ebike Atlas frame battery mouting foot.

This mounting is suitable for our downtube Atlas casing battery(DA-5C).

The price is only for the mouting, not including the battery case.

We will solder the power connector before shipment if you also add the power connector with the frame battery attachment.

The default discharging connector of the mountin is 2P original plug, please note. If you need 6P plug for larger current, please email us after placing the order.

Ebike Jumboshark/supershark casing battery mounting foot; This battery mounting is suitable for small Jumboshark casing battery, larger Jumbo shark casing battery and super shark casing battery. If your battery has an built-in controller, this battery attachment would not fit, please note.

Ebike battery frame fixing plate/mountin base for downtube battery DS-6 case. We can solder the power plug with the required connector for you before shipment.

If you are looking for larger power connector for this mounting base, we can provide 6 pin connector for the mounting(the latest version for this case is 6 pin connector for larger current, the older version is with 6pin connector for larger current, the dimensions for the connectors are the same, just the pin numbers are different). Please check your battery discharging connectors before ordering the battery fixing plate.

Reention Dorado battery mounting base, head mounting base and bottom mounting base. The Dorado key lock is included with the mounting base.

The mountint bases for all the Dorado batteries are the same.

Normally the default discharging male connector is 2 pin(the part number is PLA0273, you can check your own connector's part number first); some ebikes needs larger discharging current, and the battery will use 6 pin connector for the battery(the part number is PLA0238). You can choose the one you need.

If your original connector is still in good condition, you don't need to choose the connector; just install your original connector with the mounting.

Ebike new polly /Jumboshark battery mounting foot.

There are two types of New polly battery mounting foot, please check the pictureS before ordering. There is also a easy way to identify the two mountings: one is with 4 blade contacts socket and the other is with 5 blade contacts socket

This mounting foot is suitable for New polly DP-4C, DP-5C, DP-6C, DP-9C, DP-2170-4C and DP-2170-5C. 

The mounting here is with 4 blade contacts sockets.