Jumbo shark casing battery connecotor: male and female. It has 5 blade contacts for the connector. There are two types of New Polly case connectors, one is with 5 blade contacts and the other is with 4 blade contacts; they are not compatible, please make sure you order the right connectors.

This 5pins connector is stuiable for the Jumbo shark case, if you are not sure it fits your case or not, please check the complete case dimension first.

This connector is suitable for Super73 R, RX and S2 series batteries. If you need a replacement battery for Super73 R, RX or S2, we can also provide it with larger WH.

Rack battery connector with 6 blade pins for ebike.

We have several rack batteries and connectors; this connector is for this rack battery

Reention battery level PCB.

New polly Jumboshark battery level LED PCB 36V 48V 52V 60 72V for indicating the battery capacity Levels

The LED PCB is suitable for DP-4, DP-5, DP-6, DP-7, DP-9, DP-2170-4C, DP-5C, DP-2170-5C, DP-9C.

The LED is sutiable for all New polly batteries;

Tigershark battery level LED PCB is the same as the downtube Atlas battery level PCB. If you are not sure about which LED level to choose, please check below our battery case first.

New polly battery case

Tigershark battery case

Atlas battery case

If you are building ebike batteries with the New polly cases, you can order different LED PCB for different batteries.

Power cable for Dorado battery, Tigershark case, Atlas case or other Reention casing battery with PLA 0273 male connector , 5 pin PLA 0049 or 6 pin PLA 0238 connector; If you order the power cable, it is better for you to choose Ø4mm bullet connector, Ø5mm bullet connector or bare wire for the end connector for controller/motor because there is a small wire rubber O seal on the mounting, other connectors would be too big to go though the wire seal(you may need to let the wire go through the wire O seal, then solder the larger connectors). The connector is soldered with cable which you can replace your old plug on the battery easily by removing the lock screw.

If you need a extension cable or conversion wire for your battery, then the big connector is not a problem. But please make sure you choose the right male or female connector when placing the order.

This power cable is suitable for the Atlas casing battery, 36V Dorado battery, 48V Dorado batteries or the Tigershark casing battery. 

The 2 pin PLA 0273 connector is the male connector(installed in the battery mounting base), it's matching 2 pin female connector is PLA 0274 connector which is installed on the battery body;  Note, the PLA 0274 looks like 5 pin connector, but the three small pins are empty, therefore we call it "2 pin" connector.

The 5 pin PLA 0049 connector is the male connector(installed in the battery mounting base), it's matching 5 pin female connector is PLA 0050 connector which is installed on the battery body;

The 6 pin PLA 0238 connector is the male connector(installed in the battery mounting base), it's matching 6 pin female connector is PLA 0239 connector which is installed on the battery body;

The default wires are 12 AWG wire, if you need 10AWG wire, please email us separately. By the way, 10AWG wire for power cable, they may be too large for the wire seal of the mounting unless you discard the wire seal when installing the power cable.

Ebike New polly /Jumbo shark battery connector(4 pins). There are two types of New polly connector, one is with 5 pins and other is with 4 pins, the two connector cannot be interchangeable. Please check your own battery connector before ordering. 

If you need the 5 pins New polly socket/connector, please order here: 5 pin New polly connector

Rubber spacer for New Polly /Jumbo shark/ Tiger shark /Atlas battery mounting.

There are two types of new polly mounting foots, one is with 4 pin socket and the other is with 5 pin socket; the 5 pin socket new polly casing battery would need 4 spacers while the 4 pin mounting base would need 3 rubber spacers.

The tigershark casing battery needs 3 spacers;

The Atlas battery needs 3 spacers.

The rubber spacer would be also suitable for other Reention downtube mounting batteries; the rubber spacers arrived in April, for the mounting rails of Reention cases, such as new polly battery, atlas downtube battery and tigershark battery, we will include the rubber spacers with the shipment.