36V, 48V, 52V battery charger with two charging voltages, 80% and 100% full charging voltages.

When you don't use the battery for a long time, it's better not to 100% fully charge the battery for storage.   

Full charging voltage for 36V battery: 40V and 42V; Charging current 2.5A;

Full charging voltage for 48V battery: 51V and 54.6V; Charging current 2A;

Full charging voltage for 52V battery: 55V and 58.8V; Charging current 2A;

This charger has no fuse because the fuse has been changed to the switch(switching between the two charging voltages).

The shortage for a charger without a fuse is the charger will be burned if you connect the charger reversing the positive and negative. 

The charger is with wide AC input voltage 110V -240V.

Ebike charger for 36V, 48V, 52V batteries with3 pins mini XLR connectorfor Reention casing batteries.

The full charge voltage for 36V 10S li-ion battery is 42V;

The full charge voltage for 48V 13S li-ion battery is 54.6V;

The full charge voltage for 52V 14S  li-ion battery is 58.8V;

For the charging connector, pin 1 for positive, pin 2 for negative, pin 3 is empty, this is the default connection; if your battery has a different connection, please send us an email after placing the charger.

For the charging current, each battery would have a maximum charging current, normally the default max charging current for the batteries would be 5A; if you want higher charging current, please contact your battery supplier to check what is the max charging amps of your battery first.

2000W alluminum alloy shell battery charger for golf car, electric car, forklift battery, electric floor scrubber battery, electric lawn mower battry etc. If you are looking for faster charger, this one would be suitable for you; if you are searching for customized charger, we can supply.

Input for the battery charger: Input: 100VAC~ 240VAC 50HZ/60HZ

Cut-off current for Lithium battery is 5% of CV as default, and it can be set between 3-10% for customers' request.

Black housing for the battery charger is also available.

1500W Alluminum alloy shell charger for e-motorcycle, sightseeing bus,  tourism bus, electric car or ev batery. We can set customized charging voltage and charging current for the battery charger. 12V80A, 24V40A, 36V30A, 48V25A, 60V20A, 72V15A, 84V10A, 96V10A etc.

There are LED indicators for charging and chared status.

Alluminum alloy shell and cooling fan enable the charger will not too be hot when charging.

The handle bar makes the charger to be carried easily.

If you don't know what voltage is your charger, please email us and we will calculate the charging voltage for you.

Single cell charger 4.2V 5A, 4.2V3A, 3.65V 3A, 3.65V 5A for battery repair or balancing; If one or two cells are defective of your pack, you may need to use a single cell charger to charge the cell untill it reach the same voltage as other cells.

There is a switch between 3A and 5A;

LED indicator for charging status.

We will install Alligator clip for the end connection which you can connect to charge single cell easily.  

Hailong G70 battery socket with 5 blade contacts.

There are 4 types of Hailong sockets, please check the pictures and the related casing battery to avoid ordering the wrong socket/connector.

If you are not sure which Hailong battery the connector adapts, please click here to check the Hailong G70 casing battery to check first: 10S tigershark/hailong battery bms

SYR in-tube battery connector, 4-pins connector, it is suitable for Avention Level battery, Frey CC battery, E-joe intube battery etc;

If your battery key has "SYR" logo, and your connector is 4 blades pins connector, then this connector will fit for your battery.

Reention EEL Pro /Mini battery mounting base with key lock;

Ride1up core 5 /LMT'D battery mounting base with key lock;

There are two types of Reention EEL battery cases, EEL-mini and EEL pro case, the mounting bases for them are not compatible; Reention EEL Mini and EEL pro are the same with width(64mm), but the Reention mini is less in height(74mm) while EEL pro case is higher(94mm); Please refer to our picture, check your original case and choose the right model for the mounting base.

CANON fuel tank battery mounting base. The mounting foot is only suitable for Canon fuel tank battery case, please check here for the battery case: Canon fuel tank battery

Reention Rhino battery case for ebike; therefore are several Rhino cases, the difference is the length, width and height, please double check your own cases before ordering.

If you are looking for Dengfu E55 E56 frame intube case, the size would be 441 x 108 x 80mm(the length 441mm including the plastic battery cover).

The case is with 5.5X2.1DC charging port and battery level LED.

If you need batteries, we can also produce the battery for you.

Reention Rhino battery connector (6 pins)

This connector is suitable for Dengfu E55, E56 frame batteries.

The price include male and female connector.

The original Dengfu E55/E56 battery would have a battery communication, our wires have no battery communication leads, please note. The battery can work normally without the battery communication being connected. 

Hailong connector with cable soldered for Hailong battery mounting; it is easy for you to replace the new connector with the old one in your mounting. If you don't have soldering tool available, this power cable would be more convenience for you to replace it. Note: this power cable only includes the 4/5pin connectors with cable soldered, if you need the plug for connecting your motor controller, we can solder for you too. The counter plug from the battery body is not included. 

There are two types Hailong connector, one is with 4 blade contacts and the other is with 5 golden round contacts, the picture shows the 4pins; we also have 5pins for your option.

There is a "+ " and "-" marks on the Hailong original connector, and we solder the red wire(positive) to + and black wire(negative) to the - as default. Please double check your own plug which one for positive and which one for negative before plugping it to your motor controller.

Ebike New polly /Jumbo shark battery connector(4 pins). There are two types of New polly connector, one is with 5 pins and other is with 4 pins, the two connector cannot be interchangeable. Please check your own battery connector before ordering. 

If you need the 5 pins New polly socket/connector, please order here: 5 pin New polly connector

36V ebike battery with Reention Dorado cases which is built into the bike frame.

There are several Dorado cases with different dimension, but if the length is the same, different length or width cases are interchangeable which means you don't need to change the bike frame if you want a larger battery for more mileage.  

Reention develop 21700 Dorado case this year, therefore the max capacity could be 36V  30AH with the Samsung INR21700 50E cells. If your bike has an original Dorado battery and you want to have a larger mileage, then the 21700 Dorado case would be suitable for you. Please note the height for 21700 Dorado case would be 5mm higher than Dorado 18650 cases.

Please measure the length of your original Dorado cases before ordering. cases are compatible with the same length.

Some customers may measure the longest part of the case, our cases is 505mm by the longest part of the case.

Dengfu frame battery mounting bracket with key lock;

Dengfu has upgraded the mounting base, the upgraded base is better in drainage.

There will be an ON/OFF switch and a 5.5x2.1DC charging port soldered with the bottom mounting bracket which can be used for the Dengfu frame directly. 

If you prefer to make a custom connection for the mounting bracket, please email us after placing the order. If you also need the Dengfu battery, please order from here: 48V Dengfu battery

We have two types of the battery mounting base, one is alloy mountings and the other is plastick mounting. We currently only have the plasic mountings available, please note.

Rack battery connector with 6 blade pins for ebike.

We have several rack batteries and connectors; this connector is for this rack battery

Reention Dorado battery mounting base, head mounting base and bottom mounting base. The Dorado key lock is included with the mounting base.

The mountint bases for all the Dorado batteries are the same.

Normally the default discharging male connector is 2 pin(the part number is PLA0273, you can check your own connector's part number first); some ebikes needs larger discharging current, and the battery will use 6 pin connector for the battery(the part number is PLA0238). You can choose the one you need.

If your original connector is still in good condition, you don't need to choose the connector; just install your original connector with the mounting.

Ebike Hailong battery capacity level LED PCB 36V 48V 52V for replacement; Hailong style batteries share the same battery level LED PCB.

If you are not sure your battery case is Hailong style batteyr or not, please check the following cases which share the same Hailong battery level LED PCB:

Hailong 01 case: Ebike Hailong 01 case -greenbikekit.com BBS, ebike batteries, Bafang M620, Bafang M600, Bafang M500, Bafang M510, KT controller with display-GreenBikeKit.com

Hailong 02 or Hailong G80 case: ebike new downtube battery case for diy battery pack-Greenbikekit.com BBS, ebike batteries, Bafang M620, Bafang M600, Bafang M500, Bafang M510, KT controller with display-GreenBikeKit.com

Hailong G70 casing battery: 36V 24AH eBIKE Hailong G70 battery -Greenbikekit.com BBS, ebike batteries, Bafang M620, Bafang M600, Bafang M500, Bafang M510, KT controller with display-GreenBikeKit.com 

Reention battery level PCB.

New polly Jumboshark battery level LED PCB 36V 48V 52V 60 72V for indicating the battery capacity Levels

The LED PCB is suitable for DP-4, DP-5, DP-6, DP-7, DP-9, DP-2170-4C, DP-5C, DP-2170-5C, DP-9C.

The LED is sutiable for all New polly batteries;

Tigershark battery level LED PCB is the same as the downtube Atlas battery level PCB. If you are not sure about which LED level to choose, please check below our battery case first.

New polly battery case

Tigershark battery case

Atlas battery case

If you are building ebike batteries with the New polly cases, you can order different LED PCB for different batteries.

Dengfu E10 E22 E23 frame Battery connector, not suitable for other Dengfu frame battery.

Rubber spacer for New Polly /Jumbo shark/ Tiger shark /Atlas battery mounting.

There are two types of new polly mounting foots, one is with 4 pin socket and the other is with 5 pin socket; the 5 pin socket new polly casing battery would need 4 spacers while the 4 pin mounting base would need 3 rubber spacers.

The tigershark casing battery needs 3 spacers;

The Atlas battery needs 3 spacers.

The rubber spacer would be also suitable for other Reention downtube mounting batteries; the rubber spacers arrived in April, for the mounting rails of Reention cases, such as new polly battery, atlas downtube battery and tigershark battery, we will include the rubber spacers with the shipment.

Ebike new polly /Jumboshark battery mounting foot.

There are two types of New polly battery mounting foot, please check the pictureS before ordering. There is also a easy way to identify the two mountings: one is with 4 blade contacts socket and the other is with 5 blade contacts socket

This mounting foot is suitable for New polly DP-4C, DP-5C, DP-6C, DP-9C, DP-2170-4C and DP-2170-5C. 

The mounting here is with 4 blade contacts sockets.

e-bike fuel tank battery case for large AH battery, it can max hold 117pcs 18650 Cells or 91pcs 21700 cells. There are two types of fuel tank battery cases, the mounting bases are the same, the only difference is the height please note. 

Battery level is available for the case; the charging port is 5.5X2.1 or 5.5x2.5DC port.

The larger AH you have for your battery, the more mileage you can get for single charge.

Size: 381 x 183 x 126mm 91pcs 18650 cells or 65pcs 21700 cells;

Size: 381 x183 x 167mm for 117pcs 18650 cells or 91pcs 21700 cells;