Bafang M620 /M400
-
Bafang M400 /M300 /M420 display harness/ EB-BUS 1T4 / 1T3/ 1T2/ 1T1
Bafang M420, M300, M400, M620, G330, G360, G510 UART EB-BUS cable/bafang display wire for M400 M420 M300 M620 motor
There are two types of EB-BUS cables, one for UART motor and the other for CANbus motor, for UART motors, there are 4 types EB-Bus cables, and for CANbus motor, there are another 4 types cables, please check our pictures before placing the order.
UART motor has a round green connector for the display while CANbus motor has a triangle green connector for the display.
Bafang motor main harness 1T3, connecting the display, a pair of e-brakes, cable length: 1.2m;
Bafang Motor EB-BUS 1T2, connecting the display and one brake, cable length: 1.2m;
Bafang motor main harness 1T1, connecting the display, cable length: 850~930MM.
Bafang motor 1T4 EB-BUS cable, connecting the display, two e-brake grips, and one throttle.
If your original Bafang M400 motor is with 1T1 EB-BUS and you want to add a throttle function for your ebike, please choose the 1T4 EB-BUS. The throttle function only works after starting with pedaling the ebike, please note.
If your Bafang M400 G330 motor is with 1T3 EB-BUS and you want to add a throttle function for your ebike, please choose the 1T4 EB-bus. The throttle function only works after starting with pedaling the ebike, please note. Important tips: the throttle for the Bafang M400 motor only works under load with the pedal speed reaching 10km/h.
The display connector is with 5 pin round connector which means for UART protocol; if your display is wiht triangle 5 pins connector, then it is a CANbus motor and you will need CANbus EB-BUS cable, please note.
-
Bafang G330 M400 steel reduction gear set with cover
Bafang M400 reduction gear for replacement; the Bafang G330 motor steel cover is included.
The item includes motor gasket, reduction gear and gear cover/motor casing as shown in the picture.
For how to replace the reduction gear cover, please refer to the following vedio.
-
Bafang M400/ G330 barebone motor 36V/43V/48V 250W/350W
Bafang Max drive M400 /G330 barebone motor.
If your motor is "old age" and defective, you can buy a new barebone motor to replace it.
The are two protocols for Bafang G330/ M400 motor, UART and CAN, UART motor is with 3 pins speed sensor cable, and CAN motor is with 4 pins speed sensor cable, UART motor's display is round connector which CAN motor's display is triangle connector. If you don't know how to identify, please email us.
How to check your max drive G330 motor is UART or CAN protocol? Check the original display connector, UART protocol is with round 5pin connector display which CAN protocol is with 5pin triangle connector display.
If you need complete set of Max drivec M400, please email us.
Bafang M400 G330 motor take apart:
-
Bafang Ultra M620/ G510 mounting bolts /nuts /washers
Bafang Ultra M620/ G510 mounting bolts /nuts /washers, including chain wheel lock nut and the other bolts as shown in the picture.
If you need a special spanner for the chainwheel lock nut, please check from here: Bafang M620 chainwheel lock nut wrench
-
Bafang Ultra G510 motor stator/Bafang Ultra M620 stator/ windings for replacement
Bafang Ultra m620 G510 motor stator for repair;
Bafang ultra M620 motor windings for replacement.
If your Bafang M620/G510 motor gets error 08, it could be the stator or controller failure.
The M620 motor needs calibration after replacing the stator, UART motor use our special 961 display for the calibartion and CANbus M620 motor needs Bafang Besst tool for calibration.
For How to remove Bafang M620 stator, please check the following video:
-
Bafang M620 M600 M510 M560 M500 M420 crank arm bolt/ screw
Bafang M620 M600 M510 M500 M420 crank arm bolt/ screw;
-
Bafang right thumb throttle/accelerator for Bafang BBS/ Ultra M620/M400/M500/M600 motors
Thumb throttle/accelerator for Bafang central driven motor kit bbs01, bbs02, BBSHD, Ultra G510 M620, Max drive M400, M420, M500, M600 or M800 mid motors.
Note: This throttle also fit for Bafang Max Drive M400 G330 motor, but you need to change to a 1T4 EB-BUS, otherwise you cannot connect the throttle to your Max drive unit.
-
Bafang DP C010 display(CANbus)
Bafang DP C010.CB display, the latest Bafang HMI, it supports Bafang Go+
Bafang DP C010.CN display, the latest Bafang HMI, it supports Bafang Go+, and it has navigation mapping function(when the user uses the HMI with BAFANG GO+. When the user starts navigation with the app, the navigation route will map to the HMI in real time. For detailed operation, see BAFANG GO+ App Operation Manual.)
The display has 6 languages for option: English, German, Dutch, French, Italian and Czech.
The DP C010.CN with unlocking speed function works for newer motor firmware only such as M560, M510 with newer firmware.
The display is CANbus display, it cannot work with UART Bafang motor, please note.(CANbus display is with triangle connector while UART display is with round connector, please check).
-
$12.00 As low as: $10.00Bafang bbs M400 M300 M200 M210 motor crank arms
Bafang BBS crank arm; bafang M400 /m300/m200/M210 crank arms
-
Bafang G330 M400 36V 43V Motor windings/stator/ rotor/ core
Bafang G330 motor core, including Bafang 36V M400 stator or rotor for replacement.
Bafang M400 motor windings is easy to disassemble and replace.
The Bafang M400 G330 motor core are sourced directly from Bafang.
The UART protocol controller will have a "U" mark on the controller, it's EB-BUS connector is with female connector and the display for the motor would be UART protocol with a 5 pin round connector.
If the display connector is with triangle connector, then it is with CAN protocol. The back of the display may also mark “CAN".Replacing the CAN motor core, you may need to recalibrate the motor.
For how to replace the motor core, please check video below:
