9 pin motor extension wire with waterproof connector; this cable is suitable for standard 250W/350W motor.

This extension wire is compatible with our own 9 pin motor wires. 

Wire length: 100cm

E-bike 6V LED headlight suitable for Bafang BBS. Input: AC6V ; Cable length: 1.5M

Connector matching for Bafang BBS01/BBS02B controller's headlight plug, red wire for positive, blue wire for negative.

DPC18 display has a "headlight" button; for 965 and 961 display, press "+" button and hold for 3 seconds, the headlight will switch on/off.

If you use it for Ultra M620 mid motor, Bafang M400 motor, M420 or Bafang M300 motor, this 6V LED headlight will also be suitable for these mid drive motors. Please make sure you have the Bafang motor light connection cable.

Wuxing headlight and  speaker for bicycle. We also provide a Wuxing two in one switch for the headlight.  The matching connectors will be provided with the headlight and switch. The headlight is suitable for a 12V-80V battery.

If you also need a rear light for your ebike, we also provide 6V LED taillight suitable for 6V-60V batteries. The rear light can be installed on the e-bike rack or the seatpost tube.

The bike is installed on the front fork as shown in the picture.

Headlight Waterproof grade: IPX4

All the cables and connectors will be soldered before shipping.  If you ordered the battery on our website, we will order the matching connector with the battery too. If not, you may need to solder the two power cables to your battery mounting. If you don't want to do the soldering job, you can order an extra mounting on our website, and we will solder the matching discharging connector and light power cable/connector for you. We provide varies battery mountings for backup. 

E-bike rear light 6V LED

1. Input: DC 6V-60V

2. Output: 6V

3. Power: 0.6W

4 It can be powered by your ebike battery from 6V to 60V;

5. Cable length:  1.5M

6. You may need an ON/OFF switch to control the rear light;

7. This rear light can be mounted on the bike rear rack or on the seatpost tube. We will provide the matching backet.

8. If you also need a ebike headlight, you can order on our website, we can solder the rear light and head light to be controlled by one on/off switch.

KT-V12L Kunteng Dual hall 12 poles, 12 magnets pedal assisting sensor for ebike; it is easy to install on left side of the BB.

Cable length: 80cm 

Cable connection: 

Brown wire ---> +5v

Black wire---> Negative Electrode

Yellow wire ---> Signal

Note: This PAS only work with KT controller. Also,Kunteng controller normally set C1 = 2 as a defaullt setting for the 8 pole PAS, if you want to use 12 poles PAS, please set C1 =6 via the display, otherwise the PAS may not work.

Split 12 magnets dual hall sensor with higher accuracy for electric bikes. It is easy to install with the split PAS. No need to remove the crank; Only plug the split magnets arount the bottom bracket axle, then fix the sensor on the seat tube.

The PAS fits our KT series controllers.

Hidden wire brake sensor can use normal brake, without the use of special brake lever. Sensor installed on the soft shaft of the brake, detection the movement of brake lines online. HWBS is a long life, small volume, free maintenance, micro-consumption electronic, low voltage power supply, non-contact detection of magnetic sensors. Internal PLL circuit can ensure the stable output even use in vibration situations.

Effective Rim Diameter(ERD): 28"/700C--590mm; 26"--537mm; 20"--378mm; 16"--278mm

3-pin charging cable and charging port forJumboshark/Supershark casing battery. There are similar 3 pin charging port in the market, please make sure your battery key has the "Reention" logo, other brand 3 pin charging port would not fit. 

This charging carble and connectors are only suitable for Jumbo shark or Super shark casing batteries, Dorado batteries or other Reention casing batteries, please note.

Please make sure the pins are matching when you try to replace this charging cable to your old charging cable.

This charging cable enables your battery can be charged with larger current.

The cable length is 100cm.

Please check the below video for how to replace the charging cable from the inside of the charger: