36V batterie for e-bike; this li ion battery is mounted on the bike frame;  It could be a powerbank because it has a 5V USB output for mobile or ipad charging. It is high power and can run long distance per charge because it hashigh power.  A 180W42V4A charger for your option. If you are running a Bafang BBS motor and want a high power battery, this one would be suitable for you.

If you need a spare charger for this battery, please order from here: 120W 42V2.5A Alloy charger;

Power cable for Dorado battery, Tigershark case, Atlas case or other Reention casing battery with PLA 0273 male connector , 5 pin PLA 0049 or 6 pin PLA 0238 connector; If you order the power cable, it is better for you to choose Ø4mm bullet connector, Ø5mm bullet connector or bare wire for the end connector for controller/motor because there is a small wire rubber O seal on the mounting, other connectors would be too big to go though the wire seal(you may need to let the wire go through the wire O seal, then solder the larger connectors). The connector is soldered with cable which you can replace your old plug on the battery easily by removing the lock screw.

If you need a extension cable or conversion wire for your battery, then the big connector is not a problem. But please make sure you choose the right male or female connector when placing the order.

This power cable is suitable for the Atlas casing battery, 36V Dorado battery, 48V Dorado batteries or the Tigershark casing battery. 

The 2 pin PLA 0273 connector is the male connector(installed in the battery mounting base), it's matching 2 pin female connector is PLA 0274 connector which is installed on the battery body;  Note, the PLA 0274 looks like 5 pin connector, but the three small pins are empty, therefore we call it "2 pin" connector.

The 5 pin PLA 0049 connector is the male connector(installed in the battery mounting base), it's matching 5 pin female connector is PLA 0050 connector which is installed on the battery body;

The 6 pin PLA 0238 connector is the male connector(installed in the battery mounting base), it's matching 6 pin female connector is PLA 0239 connector which is installed on the battery body;

The default wires are 12 AWG wire, if you need 10AWG wire, please email us separately. By the way, 10AWG wire for power cable, they may be too large for the wire seal of the mounting unless you discard the wire seal when installing the power cable.

Rack battery 36V for ebike: This battery has a taillight with its case, battery capacity level is also available. The battery has a fuse too. Power switch and key lock are also available for the battery which you don't worry your battery will be stolen. 

If you also need a rack for the battery, please note our rack is only suitable for 26" bike with V-brake. It will not fit for disc brake.

The battery case has a space for ebike controller, please double check the controller size before considering put the controller with the case.

Safety note: we don't recommend the 36V 500W motor to work with this battery because the discharging connector cannot bear 25A current continuously according to the case supplier.

If you need an extra connector for this battery, please click here: 6 pin rack battery connector 

36V14AH lithium ion bottle battery for electric bicycle, 345x91mm(Height x Diameter), made with LG INR18650 MJ1 cells, Panasonic NCR18650BD, Samsung INR18650-32E or Samsung INR18650-35E(10S4P); including mounting cardle. The larger capacity, the longer road you can ride with the bike.

ON/OFF switch on the bottom of the battery;

LED capacity indicator on the head of the battery to check battery capacity.

The key lock enables the battery fastens on the mounting cradle.

36V ebike compact battery with customized battery size and light weight. BMS-10S-25/60A is built in with the battery; alloy chargers for options. The battery is made by premium cells; it has no battery case, but we have cell holders for building the battery to protect the cells.

36V14AH -17.5AH ebike battery with frog casing, can be mounted on the bicycle frame;  We only use Samsung, Panasonic or LG cells for our ebike batteries.

Headway 38120S lifepo4 battery pack 36V10AH with high c-rate, you can choose different discharging current for your demand.  BMS is included with the battery.

36V li-ion rear rack battery. This battery is suitable for Bafang BBS kits. This rack battery does not need special rack to mount it, you can mount it on any rack you have with the fixing plate and bar we provide.

Ebike Jumboshark/supershark casing battery mounting foot; This battery mounting is suitable for small Jumboshark casing battery, larger Jumbo shark casing battery and super shark casing battery. If your battery has an built-in controller, this battery attachment would not fit, please note.

ebike Jumbo shark new polly case for e-bike downtube battery; We have models of this case, DP-9, DP-6 and DP-5.  

DP-9 case can max hold 91pcs 18650 cells: 368x90x140mm.

DP-7 case can max hold 70pcs 21700 cells: 368 x 95 x 150mm;

DP-6 case can max hold 70pcs 18650 cells: 368*90*113mm;

DP-5 case can max hold 56pcs 18650 cells:  368*90*96mm.

The discharging connectors and mountings are the same for the above cases. 

If you are looking for  larger capacity for the battery, DP-9 or DP-7 model would be an ideal;

4 level LED capacity showing(for 36V, 48V, 52V, 60V or 72V battery capacity indication); if you need some extra new polly battery level LED PCB for different voltages, please order on our website.

ON/OFF switch and Keylock;

5pin discharging port; 

Round 5.5*2.1DC port or 5.5*2.5DC port for charging; If you prefer larger charging current for the pack, you can use the 3pin charging connector for the case.

Waterproof grade IPX4

The BMS used for this battery case should be thinner if you are going to build the  pack with 14S5P 70pcs cells using DP-6 case. We can provide you the matching BMS for this polly battery case.

Reention Dorado battery, EEL battery, tigershark, Atlas battery connector:  2 pins, 5 pins or 6pins. 6P is for larger Amps demand.

These are the original connectors for the tigershark battery or Atlas frame battery, male and female.

This mounting connector is also suitable for other Reention cases, you can check the dimension before placing the order.

2 pins connector male number: "PLA0273",  female part number"PLA0274". Another 2 pins connector male number is PLA0379, and matching female part(with a small PCB on the back) is PLA0378.

6 pins female part number: PLA0239, 6pin male part number: PLA0238; If the part number is the same as your original's then this plug will also fit for your case. 

If you need the power cable soldered with this plug, please order from here: Tigershark/ Atlas/ Dorado power cable with PLA 0273 plug

Ebike downtube battery fixing base/mounting foot. This battery mounting is only suitable for Hailong-1 casing battery.

There are two types of discharging connector: one is with 4pin blade contacts and the other is with 5pin round golden contacts. Please check your own battery discharging connector before placing the battery mounting.

For 4pin connector: we solder the positive and negative power cable according to the marks "+" and "-" on the connector housing, please check your battery body's postive and negative poles before connect the battery to the motor. 

For 5pin connector:  we solder the positive and negative power cable according to the marks "+" and "-" on the connector housing, leave the rest 3 small pins empty, please check your battery body's postive and negative poles before connect the battery to the motor. 

If you have special demand for the discharging connector positive and negative side, please email us after ordering the mounting.

Hailong case discharging connector 4 blade contacts, 5 round contacts or 6 round contacts, fit for Hailong 01, Hailong 02 or Hailong 03 casing battery.  Please note They are not suitable for Hailong 01 Pro battery; the hailong 01 Pro case use 5 blade contacts connector al though the housing is similar but not compatible.

There are 3 types of connectors for Hailong case, the outter dimensions are the same, only the contacts are different, one is with 4 blade contacts, one is with 5 golden round contacts and the rest is with 6 round coontacts. Please check your own Hailong connectors before placing the order.

20A< 4 pin connector<25A; 25A <5 pin connector <30A; 

 30A < 6 pin connector <35A;

Key lock for e-bike downtube Hailong-01 casing battery.

This Key set is fit for Hailong-01 casing battery, please note.

For how to replace the Hailong Key lock, please refer to the following video:

ebike Atlas frame battery mouting foot.

This mounting is suitable for our downtube Atlas casing battery(DA-5C).

The price is only for the mouting, not including the battery case.

We will solder the power connector before shipment if you also add the power connector with the frame battery attachment.

The default discharging connector of the mountin is 2P original plug, please note. If you need 6P plug for larger current, please email us after placing the order.

Ebike battery frame fixing plate/mountin base for downtube battery DS-6 case. We can solder the power plug with the required connector for you before shipment.

If you are looking for larger power connector for this mounting base, we can provide 6 pin connector for the mounting(the latest version for this case is 6 pin connector for larger current, the older version is with 6pin connector for larger current, the dimensions for the connectors are the same, just the pin numbers are different). Please check your battery discharging connectors before ordering the battery fixing plate.

Jumbo shark casing battery connecotor: male and female. It has 5 blade contacts for the connector. There are two types of New Polly case connectors, one is with 5 blade contacts and the other is with 4 blade contacts; they are not compatible, please make sure you order the right connectors.

This 5pins connector is stuiable for the Jumbo shark case, if you are not sure it fits your case or not, please check the complete case dimension first.

This connector is suitable for Super73 R, RX and S2 series batteries. If you need a replacement battery for Super73 R, RX or S2, we can also provide it with larger WH.

e-bike rear rack battery discharging connector with golden banana pins.

The default connector has 5 golden pins, two big pins and 3 small pins, some battery suppliers may only solder two big pins, if so, you can just ignore the rest 3 small pins.

Note, there are several rear rack casings with different connectors, please double check your original connectors before ordering.

Packing list: A pair plug including golden pins